BMW E81 E82 E90 E92

The Mantis Kit for the BMW E8x is the most relevant angle kit in today's drift society, keeping cost in mind without sacrificing quality or performance. The FDF kit is the first utilizing the factory knuckle and its strut, caliper and bearing mounts, while attaching the lower half to the FDF adaptor to get the perfect geometry, adjustment and bump stops.

DOES NOT WORK WITH M SERIES KNUCKLES

-Angle, 70 degrees depending on your wheel setup and length of control arms

-Tie-rods, Outer tie-rods  included, these fasten to the stock inner tie-rods 

-Ackerman, adjustable Ackerman options from Positive - zero - negative 

-Roll Center, optimized handling by adding 40mm of roll center correction

-Bump steer, perfected bump steer for drifting

-Caster, modifications made to the displaced caster amount giving a good self-steer feel for the driver and maximizing the performance for drifting

-Camber, optimized camber ranging from -3 to -6

-Track Width, 50-75mm wider per side creating a stable and high clearance front end

-Suspension Travel, long travel range, full lock to full lock at any point throughout  suspension travel for increased grip 

-Joints, Chromoly heim joints, and spherical bearings with self-lubricating nylon race, easily replaceable 

-Weight Reduction, compact drop knuckle design makes for a lightweight and strong design, 7075 aluminum used where possible which provides steel like strength at 40% weight reduction. 

 INSTALLATION GUIDE

Please allow 2-3weeks of fabrication before the item is sent.

The Mantis Kit for the BMW E9x is the most relevant angle kit in today's drift society, keeping cost in mind without sacrificing quality or performance. The FDF kit is the first utilizing the factory knuckle and its strut, caliper and bearing mounts, while attaching the lower half to the FDF adaptor to get the perfect geometry, adjustment and bump stops.

DOES NOT WORK WITH M SERIES KNUCKLES

-Angle, 70 degrees depending on your wheel setup and length of control arms

-Tie-rods, Outer tie-rods  included, these fasten to the stock inner tie-rods 

-Ackerman, adjustable Ackerman options from Positive - zero - negative 

-Roll Center, optimized handling by adding 40mm of roll center correction

-Bump steer, perfected bump steer for drifting

-Caster, modifications made to the displaced caster amount giving a good self-steer feel for the driver and maximizing the performance for drifting

-Camber, optimized camber ranging from -3 to -6

-Track Width, 50-75mm wider per side creating a stable and high clearance front end

-Suspension Travel, long travel range, full lock to full lock at any point throughout  suspension travel for increased grip 

-Joints, Chromoly heim joints, and spherical bearings with self-lubricating nylon race, easily replaceable 

-Weight Reduction, compact drop knuckle design makes for a lightweight and strong design, 7075 aluminum used where possible which provides steel like strength at 40% weight reduction. 

Installation Guide

Please allow 2-3weeks of fabrication before the item is sent.

FDF's rear toe arm allow you to achieve correct rear toe on your car. The factory BMW suspension has a very aggressive camber gain through compression - this is extremely noticeable when lowered. FDF's rear arms also eliminate deflection found in the stock bushings. Instead of using rubber, FDF uses 3/4" Teflon lined rod ends. 

Technical Specifications:

• Black Anodized and machined from 6061-T6 aluminum
• Stainless Steel misalignment spacers
• Low Friction 3 Piece Teflon Lined Rod Ends

FDF's rear control arms allow you to achieve correct rear camber and toe on your car. The factory BMW suspension has a very aggressive camber gain through compression - this is extremely noticeable when lowered. When you lower your vehicle, it naturally adds more camber - these upper arms allow you to correct that rear camber to give you more grip. FDF's rear arms also eliminate deflection found in the stock bushings. Instead of using rubber, FDF uses 3/4" Teflon lined rod ends. 

Includes 4 arms

Technical Specifications:

• Black Anodized and machined from 6061-T6 aluminum
• Stainless Steel misalignment spacers
• Low Friction 3 Piece Teflon Lined Rod Ends