hyundai

The Mantis Kit for the Genesis is the most relevant angle kit in today's drift society, and here's why:

-Angle, 65 degrees+ depending on wheel size and track width

-Ackerman, Adjustable ackerman

-Roll Center, optimized handling by adding 50mm of roll centre correction

-Bump steer, minimal bump steer in drift by perfecting tie-rod pitch angle

-Caster, added trail and reduced caster which adds more grip by increasing tire contact patch, causes less bump steer, less jacking from lock to lock, increase transition speed, effortless transition while on throttle

-Camber, optimized camber ranging from -3 to -6

-Track Width, 50mm wider per side creating a stable and high clearance front end

-Suspension Travel, long travel range, full lock to full lock at any point throughout  suspension travel for increased grip 

-Joints, Chromoly heim joints and spherical bearings with self lubricating nylon race, easily replaceable 

-Weight Reduction, compact drop knuckle design makes for a lighter and stronger design, scissor frame constructed arms with crumble zone to save mounting points from failing under impact, 2024 aluminum used where possible which provides steel like strength at 40% weight reduction. 

2 weeks waiting time for custom colours

For custom colours, email your order number and the colour wanted

Please allow 2-3weeks of fabrication before the item is sent.

Our new Aluminum Dual Caliper Brackets for the Genesis chassis. Made out of 6061 Billet Aluminum and made entirely in house. 

Comes with required hardware to install.

Fits both Brembo and Non-Brembo Calipers.

Some trimming may be needed on the knuckle.

Please allow 2 weeks for fabrication before the product ships.

The Hyundai Genesis hydro plate allows you to easily bolt a handbrake in your car using the factory shifter holes provided.

This bracket will require you to either trim or remove your centre console plastics. 

Adjustable sway bar links

These Adjustable links are a high quality Chromoly female and male rod end. They are length adjustable and a universal way to connect your sway. Adjustable sway bar links are also used to load one side of the car vs another, this can be beneficial when corner balancing a car, or setting up your car to handle different tracks. 

They use m12 hardware (bolts and nuts) 

The length range is from 3.3" - 4.4" centre of bearing to centre of bearing.

Universal hood vents or send us an email for a custom size!

We can also scale the available sizes to fit your application. For example, if you wanted the Curved design, but only 24" tall, we would simply scale it down to that size. The widths will also get smaller with the scale. 

-26" tall 
-30" wide top 
20.5" wide bottom

The FK rod end bearings are the premium option for our angle kits that offer supior bearing life, extreme strength and a smooth feel. We offer them in 2 sizes, both left hand (LH) and right hand (RH).

The JMX10 is a PTFE lined 5/8-18 bearing with a yield strength of 17,959 lbs.

The JMX12 is a PTFE lined 3/4-16 bearing with a yield strength of 28,090 lbs.

Chromoly Housing, 3 piece high-performance Teflon race

Bearing Race: 3 piece teflon

Ball: heat treated, hard chrome plated bearing steel

Finish: bright polished chrome

Housing: 4130 heat treated chromoly steel

Application: Our Chromoly rod ends are ideal for automotive after market suspensions such as control arms, end links and ball joints. 

Ultimate Static Load Rating 3/4 : 25,489 lbs

Ultimate Static Load Rating 5/8 : 19,751 lbs

Our rigid tie-rod for the FDF Mantis kits.

Quantity- Price is for 1 tie-rod 

Material- 7075 Aluminum

Benefits over regular tie-rods  

• Very stiff design, does not flex like the thin steel tie-rods, this improves handling.
• Machined fail point to save your steering rack on impact.
• Stronger than steel but super lightweight.

We have 7 lengths that currently go with there corresponding angle kits, please select one of the 7 options for your kit

4.5" long (these have a m14x1.5 RH thread, and a 5/8-18 LH thread)

-Corvette, S197, Genesis

6.5" long (these have a m14x1.5 RH thread, and a 5/8-18 LH thread)

- S550, SN95, 370Z mini

8.5" long (these have a m14x1.5 RH thread, and a 5/8-18 LH thread)

-E36, FRS base, 

9.5" long (these have a 5/8-18 RH thread, and a 5/8-18 LH thread)

- 350Z reg

10" long (these have a m14x1.5 RH thread, and a 5/8-18 LH thread)

-E46

11.5" long (these have a 5/8-18 RH thread, and a 5/8-18 LH thread)

-240sx, 350z mega, is300/jzx, 

13" long (these have a 5/8-18 RH thread, and a 5/8-18 LH thread)

-E46 full tierod setup, frs power kit, 

Steering column kit  includes the following:

 -Bolts to any 1.5 inch roll cage tubing

- 44" of steering shaft 

- 1 column mount

- 1 sweet u-joint

- 1 firewall bearing 

- 1 quick release "Option"

-Comes in pair

-Universal fit

-High quality wrap sticker

FDF Raceshop Hats

1. Snapback, Black hat with white lettering

2. Snapback, Nardo Gray hat with white lettering

-Includes "race shop" on the drivers side 

-Instant respect from the drift gods

The FDF Toe Plates are the quickest and simplest way to measure toe at home or at the track.

You can choose to buy with or without two Lufkin measuring tapes.

Please allow 1 week before shipping.

Introducing the FDF Sway Bar Kit, an innovative solution that simplifies the process of creating a custom sway bar for your race car. Our kit features precision-machined components, meticulously crafted in-house to ensure superior quality and performance. With this comprehensive kit at your disposal, you'll have everything you need to construct a custom sway bar, from start to finish.

The FDF Sway Bar Kit includes all the complex parts required to build a top-of-the-line sway bar, along with convenient links to help you source any additional materials you may require. Whether you prefer to purchase materials locally or through the McMaster-Carr website, we've got you covered.

To further assist you in customizing your sway bar, we offer a range of options to choose from. Simply refer to the detailed information provided below and select the options that best meet your specific needs.

For a visual demonstration of how our kit can be utilized in your build, we encourage you to check out our video link, showcasing how we used the FDF Sway Bar Kit in our C6 Corvette build.

Invest in the FDF Sway Bar Kit and take your race car to the next level of performance and precision.

Included Parts

-2 Female spline ends

- 2 Male Spline ends

- 4 locking bolts

- 2 blades (6",8" or 10")

Optional 

-sway bar link kit

Need to purchase parts 

- 2 Bushings 

- sway bar material (4130 1.25x.120 tubing)

- housing material (DOM or 4130 1.75 x .120 tubing)

 Please allow 2-3 weeks for shipping